空壓清洗的方法： The method of air pressure cleaning: 先把空壓機運轉幾分鐘，機油達到常溫； First run the air compressor for a few minutes, and the oil reaches normal temperature. 關閉空壓機，等內部壓力泄完，打開加油蓋，倒進空壓機清洗劑，擰緊加油蓋； Turn off the air compressor, and when the internal pressure is released, open the fuel cap, pour the air compressor cleaning agent, and tighten the oil filler cap. 打開空壓機運轉30分鐘； Open the air compressor for 30 minutes. 放掉舊機油，然后加進新機油。 Get rid of the old oil and add the new oil. 一般清洗后的空壓機型線 流水槽模具 景觀石 檢查井鋼模具 保定通風管道 隔離墩模具 保定保潔公司溫度會下降10度左右。 The temperature of the air compressor after general cleaning will drop about 10 degrees. 二、冷卻器清洗 Two. Cleaning of cooler 在國內，空壓機的冷卻器一般分風冷式和水冷式兩種，因此針對不同的冷卻器，有不同的清洗方法。 In China, the cooler of air compressor is generally divided into two types: air-cooled and water-cooled. Therefore, there are different cleaning methods for different coolers. 2.1風冷型冷卻器 2.1 air cooling type cooler 打開導風罩清理蓋板，或拆下冷卻風扇； Open the air shield to clean the cover plate or remove the cooling fan. 用壓縮空氣反吹將污物吹下，再把污物拿出導風罩；如果較臟，應噴一些除油劑再吹。螺桿空壓機當無法用以上方法清理時，需要將冷卻器拆下，用清洗液浸泡或噴沖并借助刷子（嚴禁使用鋼絲刷）清洗。 Use compressed air to blow down the dirt, then take the dirt out of the wind shield. If it is dirty, spray some degreasing agents and blow again. When the screw air compressor can not be cleaned with the above methods, it is necessary to remove the cooler, soak or spray with the cleaning liquid and wash it with the brush (strictly forbidden to use a steel wire brush). 裝好蓋板或冷卻風扇 Load a cover or a cooling fan 2.2水冷型冷卻器 2.2 water cooled cooler 拆開冷卻水進出水管。 Disassemble the cooling water in and out of the pipe. 注入清洗溶液浸泡或用泵循環沖刷（反沖效果較好）。 Immersion in cleaning solution or scouring with pump circulation (better recoil). 用清水沖洗。 Rinse with clean water. 裝好冷卻水進出水管。 Load the cooling water into the pipe. 當油冷卻器結垢較嚴重，用以上方法清理不理想時，可以單獨拆下油冷卻器，打開兩頭端蓋，用專用清理鋼刷或其他工具清除水垢。當清理冷卻器介質側不能有效降低溫度時，螺桿空壓機需要對油側進行清理，方法如下： When the oil cooler is badly fouled, the oil cooler can be removed, the end cover of two ends can be opened, and the scale can be cleared by special cleaning steel brushes or other tools. When cleaning the coolant medium side can not effectively reduce the temperature, the screw air compressor needs to clean the oil side. 拆開進出油管； Disassemble the import and export of the oil pipe; 注入清洗溶液浸泡或用泵循環沖刷（反沖效果較好）； Immersion in cleaning solution or scouring with pump circulation (better recoil); 用清水沖洗； Rinse with clean water; 用干空氣吹干或用脫水油除水； Dry air with dry air or dehydrated oil to remove water. 裝好進出油管。 Get in and out of the oil pipe.